Civilization 6 Message Board  

Ok, so after playing the game with the trainer for a good 8 hours or so, everything seems to work fine except the selected city editor options (population, amenities, housing) is still 50/50. Also it's prob best to always remember to turn off an option before you end your turn.

Is there a way to add a text box on the selected city editor section. Like for example, when selecting a city in game (New York) the editor will show [New York] such that I know which city is selected in order to apply the new values. Just a thought from a QoL standpoint.

[Edited by drunk3nturtl3, 2/19/2019 3:04:26 PM]

AI doesn't use cheats when used as instructions say

best,
Cal

The editor works like it works. If you press TAB and it doesn't go to the next line, then YES, you have to take 0.2 seconds to click on it with your mouse.

best,
Cal

quote:

The editor works like it works. If you press TAB and it doesn't go to the next line, then YES, you have to take 0.2 seconds to click on it with your mouse.

best,
Cal



When I use the "Tab" key the cursor just goes away say from the "Unit Level" box. It does not move to the "next" unit. No matter how many times I click on the unit I want to edit the trainer will not change units.

NateLab

[Edited by NateLab, 2/19/2019 7:28:46 PM]


[Edited by NateLab, 2/19/2019 7:37:38 PM]

this makes no sense. What are you saying? You want the trainer to skip to the next UNIT when you press TAB in the trainer? No trainer does this

best,
Cal

I agree. All I want to do is to move on to another item to edit. At first I just would click on that unit but nothing would happen (say I was editing an "archer" and I wanted to edit a "warrior".) I thought it was odd myself but based on some of the previous notes I tried the "Tab" key. In short, all I want to do is edit different units but I can't do that if by whatever means I can't seem to get the trainer to change units. Sorry for the frustration on your part but I feel the same way.

Sincerely,
NateLab

People continue to refuse to read instructions, refuse to read the forums, refuse to read the sticky specifically telling people what to do and etc...

so I will post this again, and we are putting the game ON HOLD so I don't get 100 messages of people saying trainer don't work every day.

Almost nobody reading anything...
Literally on the previous page to this one, and posted multiple times..

Trainer is for DX11 version and ONLY for Civ 6 with new DLC installed and enabled.
Also, best to activate the trainer with F1 only AFTER you are already in the game.
Directly from the README:

NOTE
=====

This trainer is for Civilization VI with the Gathering Storm Expansion ONLY! It will not work unless you own the Civilization VI Gathering Storm expansion and have it ENABLED in the "Additional Content" menu at the main menu. We NO LONGER support any other versions or expansions of the game, ONLY Civilization VI Gathering Storm will be supported from now on. This also means that if you only own vanilla Civilization VI with no expansions or only own the Rise and Fall expansion, this trainer will not work for you! You MUST own the Civilization VI Gathering Storm expansion and have it enabled!

This game dynamically loads and unloads and reloads the game .dll while you play, especially if you restart, or are loading or starting a new game. Please note that this means many options will no longer work and will need to be turned off and then turned back on, since the game is reloading the addresses in a new .dll. The best way to use this trainer is to wait until you start your game and are able to move units and click on cities BEFORE you activate the trainer. It's also best to close the trainer and restart the trainer if you restart the game, load a save, or do anything to start a new game or load a new game.

We might take it back off hold if the game patches...

best,
Cal

Read the instructions.
Trainer has been working fine.
No issues, other than activation is once in game, rather than at menu like many other trainers.
Thanks for the trainer! 😀