Steel Division 2 Trainer and Cheats Discussion - Page 4

PWizard · 4/7/2019

Steel Division 2 by cheathappens.com Activating this trainer If not state otherwis

TIER 7

Junker posted on Jun 23, 2019 11:31:39 AM - Report post

Hang with us Cal.....just know WE GREATLY APPRECIATE the services you and team provide!!

Well....my game keeps crashing after launching and playing for about 4 minutes every time. I reverted the old trainer and it works without crashes?

[Edited by vonBraun, 6/23/2019 4:18:06 PM]

ELITE

Tilvaltar posted on Jun 23, 2019 12:58:39 PM - Report post

quote:

originally posted by Timothy3636

I'm most likely doing something wrong, but when I turn the options off and then "Launch Battle" the game instantly crashes, any ideas on how to make it work? The options themselves work.

Same here.

ELITE

Trapoltini posted on Jun 23, 2019 1:37:11 PM - Report post

Hey, I've been trying out things for the past few hours to get the trainer in Campaign going.

It crashed all the time.

then I tried another trainer by another provider and that worked!

One of the things that trainer does differently is that it sets the deployment-points to 50.000 instead of the maximum possible amount.

so that might be the remedy, hope I could help!

ELITE

SirJacek posted on Jul 04, 2019 7:31:12 AM - Report post

quote:

originally posted by cledus166

So I have been only using options during deployment phase and only after about a minute so the ai is done placing units, then I turn off all options and start the match. The ai still gets all the advantages though. My question is, is there something I missed or something I am doing wrong. Thanks

edit: after messing with it a bit more I think it has something to do with the phase unlocker

edit 2: after further messing with it if you use the phase unlocker after the unlimited units and unlimited points it gives the ai the advantage as well. If you use the phase unlocker first the ai might deploy a couple more units but the will not get unlimited points and units.

[Edited by cledus166, 5/2/2019 5:31:01 PM]

Thank you

thats all true
TO PREVENT AI of getting the same trainer options :
FIRST press all phases cheat then the others if you like . Never unlock phases after other otions.

BEST

ELITE

_l3RY4N posted on Jul 05, 2019 2:33:25 AM - Report post

Just a suggestion:
instead of just not substracting the amount of units you placed from the units you have how about the trainer sets it to a high number/add 99 units so that one wouldnt need to activate the option during the fight..

that way after you placed every unit atleast once during deployment phase you would have a lot of units, more than one will ever need, and the ai wouldnt benefit from the effects of the trainer..

i do this in a similar way with the current trainer.. just place the units and remove them again. that way it raises the unit count. i do that again and again until i have the desired amount of that unit.. repeat with every unit you have and done. takes a while though.

tip: hold CTRL to place all units of that unitcard/type/thingy and zoom out so you can remove all of those units you just placed with just 1 klick

ELITE

oozakibr posted on Jul 05, 2019 1:33:49 PM - Report post

Is someone using the Time function? I dont know how to use it.

ELITE

SirJacek posted on Jul 06, 2019 3:26:08 AM - Report post

dont know to

ELITE

Predoc posted on Jul 16, 2019 9:07:40 AM - Report post

I have the AI issue right on from starting the last Campaign "Barnovici-something" as axis. Being forced into the first defensive battle I started the trainer. F1 and just activating unlimited troops and req-points, placing my troops, deactivate the activated options and launch the battle.

But the ai still rushes me with huge amount of troops, which it couldn't have. Did I miss something or can somebody confirm my issue?

Steel Division 2 Message Board