11:32:27: Civilization VI Gathering Storm, 1.0.12.9 564030 05-02-2021 (STEAM/EPIC)
11:32:33: Successfully attached to CivilizationVI_DX12
11:32:33: Capture Unit Base Address, Script error in line 6: The module name 'GameCore_XP2_FinalRelease.dll' does not exist!
11:34:12: Successfully attached to CivilizationVI_DX12
11:34:13: Capture Unit Base Address, Script error in line 6: The module name 'GameCore_XP2_FinalRelease.dll' does not exist!
12:12:13: Successfully attached to CivilizationVI_DX12
12:12:14: Capture Unit Base Address, Script error in line 6: The module name 'GameCore_XP2_FinalRelease.dll' does not exist!
I continue getting this message.
Even when I can move the units, in a completely functional and current (All DLC) game, I still get this error when activating the trainer:
Unhandled Exception
Code: EXCEPTION_BREAKPOINT
Call Stack
-----------------------------------------------------
??? ! ??? ???, line 0
About 3 other people seem to have had this code. I have attempted to initiate the trainer:
1. Before loading
2. While Loading
3. Once fully in the game and able to move units
All while whitelisting all files, all trainers, stopping my antivirus, etc.
[Edited by DreadWraith, 1/10/2022 11:06:15 AM]
Please be aware of the Readme for this game. As this trainer has additional requirements that need to be fulfilled
"This also means that if you only own vanilla Civilization VI with no expansions or only own the Rise and Fall expansion, this trainer will not work for you! "
This trainer is for Civilization VI with the Gathering Storm Expansion ONLY! It will not work unless you own the Civilization VI Gathering Storm expansion and have it ENABLED in the "Additional Content" menu at the main menu. We NO LONGER support any other versions or expansions of the game, ONLY Civilization VI Gathering Storm will be supported from now on. This also means that if you only own vanilla Civilization VI with no expansions or only own the Rise and Fall expansion, this trainer will not work for you! You MUST own the Civilization VI Gathering Storm expansion and have it enabled!
This game dynamically loads and unloads and reloads the game .dll while you play, especially if you restart, or are loading or starting a new game. Please note that this means many options will no longer work and will need to be turned off and then turned back on, since the game is reloading the addresses in a new .dll. The best way to use this trainer is to wait until you start your game and are able to move units and click on cities BEFORE you activate the trainer. It's also best to close the trainer and restart the trainer if you restart the game, load a save, or do anything to start a new game or load a new game.
To make sure trainer works, CONFIRM THAT YOU OWN the GATHERING STORM EXPANSION. To do this in STEAM, right click the game, click PROPERTIES, then click DLC and make sure it's listed and INSTALLED.
Next in the game, click SINGLE PLAYER, then ADDITIONAL CONTENT, then MODS, then ENABLE ALL and make sure you see "Expansion: Gathering Storm" listed and ENABLED.
For EPIC, you can see OWNED next to PLATINUM EDITION UPGRADE to make sure you have the GATHERING STORM expansion, then enable it in the game as described above!
Trainer will NOT work with savegames that were saved WITHOUT EXPANSION GATHERING STORM ENABLED.
Trainer was tested 8 days ago and found working normally by Nook.
[Edited by moderator Sniper, 1/10/2022 11:24:56 AM]
Topic Name of Error:
Capture Unit Base Address, Script error in line 6: The module nameGameCore_XP2_FinalRelease.dll does not exist!
I have this game on Steam with all DLC's including the New Frontier Pass, are there any solutions to this problem?
Trainer causes the game to crash when activating any of the trainer abilities.
Link
Please make sure you read the above posts as well, this trainer requires specific DLC installed and steps to take from the Read Me